Carbide Rods
Rods with Central Coolant Hole
L=330mm (Tol.0/+5) Unit: mm
| Diameter | Hole Diameter | Centre Offset | T10 | T12UF | ||||
| ΦD | Tol. Of raw | ΦD | Tol. | a | raw | H6 | raw | H6 |
| 3 | +0.30/+0.50 | 0.50 | ±0.10 | 0.10 | ◇ | ○ | ◇ | ○ |
| 4 | +0.30/+0.50 | 0.80 | ±0.10 | 0.10 | ◇ | ○ | ◇ | ○ |
| 5 | +0.30/+0.50 | 0.80 | ±0.10 | 0.13 | ◇ | ○ | ◇ | ○ |
| 6 | +0.30/+0.50 | 1.00 | ±0.15 | 0.15 | ◇ | ○ | ◇ | ○ |
Request a quote
Rods with 2 Parallel Coolant Holes
L=330mm (Tol.0/+5) Unit: mm
| Diameter | Hole Diameter | Bolt Circle | Centre Offset | T10 | T12UF | |||||
| Tol. of raw | Φd | Tol. | TK | Tol. | a | raw | h6 | raw | h6 | |
| 4 | +0.30/0.50 | 0.80 | ±0.10 | 1.80 | +0,-0.15 | 0.10 | ◇ | ○ | ◇ | ○ |
| 5 | +0.30/0.50 | 0.80 | ±0.10 | 2.00 | +0,-0.15 | 0.13 | ◇ | ○ | ◇ | ○ |
| 6 | +0.30/0.50 | 1.00 | ±0.15 | 3.00 | +0,-0.20 | 0.15 | ◇ | ○ | ◇ | ○ |
| 7 | +0.30/0.60 | 1.00 | ±0.15 | 3.50 | +0,-0.20 | 0.15 | ◇ | ○ | ◇ | ○ |
Request a quote
Solid Long Rods-Metric
L=310mm/ 330mm (Tol.: 0/+5mm) Unit: mm
| Diameter | T10 | T10UF | T12UF | ||||
| ΦD | Tol. Of raw | raw | h6 | raw | h6 | raw | H6 |
| 2 | +0.15/+0.30 | ◇ | ◇ | ◇ | |||
| 3 | +0.15/+0.30 | ◇ | ◇ | ◇ | |||
| 4 | +0.30/+0.50 | ◇ | ○ | ◇ | ○ | ◇ | ○ |
| 5 | +0.30/+0.50 | ◇ | ○ | ◇ | ○ | ◇ | ○ |
Request a quote
Solid Long Rods-Inch
L=310mm/ 330mm (Tol.: 0/+5mm) Unit: mm
| Diameter | T10 | T10UF | T12UF | ||||
| ΦD | Tol. Of raw | raw | h6 | raw | h6 | raw | H6 |
| 2 | +0.15/+0.30 | ◇ | ◇ | ◇ | |||
| 3 | +0.15/+0.30 | ◇ | ◇ | ◇ | |||
| 4 | +0.30/+0.50 | ◇ | ○ | ◇ | ○ | ◇ | ○ |
| 5 | +0.30/+0.50 | ◇ | ○ | ◇ | ○ | ◇ | ○ |
Request a quote
Ground Rods with Chamfer
L Tol.:0/+1.0mm) Unit: mm
| ΦD | L | C | T10 | T10UF | T12UF | |||
| H5 | h6 | H5 | h6 | raw | H6 | |||
| 3 | 40 | 0.4 | ◎ | ○ | ◎ | ○ | ◎ | ○ |
| 3 | 50 | 0.4 | ◎ | ○ | ◎ | ○ | ◎ | ○ |
| 3 | 70 | 0.4 | ◎ | ○ | ◎ | ○ | ◎ | ○ |
| 3 | 100 | 0.4 | ◎ | ○ | ◎ | ○ | ◎ | ○ |
Request a quote
Ground Rods with Chamfer-Inch
L (Tol.0/+1/16) Unit: mm
| ΦD | L | Chamfer Size | T10 | T12UF | |||
| C | ToL | H6 | H5 | H6 | h5 | ||
| 1/8 | 1-1/2 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
| 1/8 | 2 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
| 1/8 | 2-1/2 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
| 1/8 | 3 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
Request a quote
Rods with 2 Helical Coolant Holes
Rods with 2 Helical Coolant Holes (30°)
L (Tol.0/+1/16) Unit: mm
| ΦD | L | Chamfer Size | T10 | T12UF | |||
| C | ToL | H6 | H5 | H6 | h5 | ||
| 1/8 | 1-1/2 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
| 1/8 | 2 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
| 1/8 | 2-1/2 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
| 1/8 | 3 | 0.015 | ±0.004 | ○ | ◉ | ○ | ◉ |
Request a quote
Rods with 2 Helical Coolant Holes (40°)
L=330mm (Tol.0/+5) Unit: mm
| Diameter | Hole Diameter | Bolt Circle | Pitch(±0.5°) | Centre Offset | T10 | T10UF | |||||||
| ΦD | Tol. of raw | Φd | Tol. | TK | Tol. | P | Tol. | a | raw | h6 | raw | h6 | |
| 6 | +1.1/+1.5 | 0.50 | ±0.10 | 2.20 | 0/-0.4 | 22.46 | -0.39 | +0.40 | 0.15 | ◇ | ○ | ◇ | ○ |
| 7 | +1.1/+1.5 | 0.65 | ±0.15 | 2.40 | 0/-0.6 | 26.21 | -0.46 | +0.47 | 0.15 | ◇ | ○ | ◇ | ○ |
| 8 | +1.1/+1.5 | 0.65 | ±0.15 | 2.70 | 0/-0.6 | 29.95 | -0.53 | +0.54 | 0.15 | ◇ | ○ | ◇ | ○ |
| 9 | +1.1/+1.5 | 0.75 | ±0.15 | 3.20 | 0/-0.8 | 33.70 | -0.59 | +0.60 | 0.20 | ◇ | ○ | ◇ | ○ |
Request a quote
Rods with 3 Helical Coolant Holes
Rods with 3 Helical Coolant Holes (30°)
L=330mm (Tol.0/+5) Unit: mm
| Diameter | Hole Diameter | Bolt Circle | Pitch(±0.5°) | Centre Offset | T10 | T10UF | |||||||
| ΦD | Tol. of raw | Φd | Tol. | TK | Tol. | P | Tol. | a | raw | h6 | raw | h6 | |
| 6 | +0.60/+1.10 | 0.70 | ±0.10 | 2.75 | 0/-0.4 | 32.65 | -0.65 | +0.67 | +4° | ◇ | ○ | ◇ | ○ |
| 6 | +0.60/+1.10 | 0.50 | ±0.10 | 2.90 | 0/-0.4 | 32.65 | -0.65 | +0.67 | +4° | ◇ | ○ | ◇ | ○ |
| 8 | +0.60/+1.10 | 1.00 | ±0.15 | 4.00 | 0/-0.4 | 43.53 | -0.86 | +0.89 | +4° | ◇ | ○ | ◇ | ○ |
| 8 | +0.60/+1.10 | 0.70 | ±0.10 | 4.00 | 0/-0.4 | 43.53 | -0.86 | +0.89 | +4° | ◇ | ○ | ◇ | ○ |
Request a quote
Rods with 3 Helical Coolant Holes (40°)
L=330mm (Tol.0/+5) Unit: mm
| Diameter | Hole Diameter | Bolt Circle | Pitch(±0.5°) | Centre Offset | T10 | T10UF | |||||||
| ΦD | Tol. of raw | Φd | Tol. | TK | Tol. | P | Tol. | a | raw | h6 | raw | h6 | |
| 6 | +1.1/+1.5 | 0.50 | ±0.15 | 2.20 | 0/-0.3 | 22.46 | -0.39 | +0.40 | +4° | ◇ | ○ | ◇ | ○ |
| 8 | +1.1/+1.5 | 0.65 | ±0.15 | 2.70 | 0/-0.3 | 29.95 | -0.53 | +0.54 | +4° | ◇ | ○ | ◇ | ○ |
| 10 | +1.1/+1.5 | 0.80 | ±0.15 | 3.50 | 0/-0.5 | 37.44 | -0.66 | +0.67 | +4° | ◇ | ○ | ◇ | ○ |
| 12 | +1.1/+1.5 | 0.90 | ±0.20 | 4.20 | 0/-0.5 | 44.93 | -0.79 | +0.80 | +4° | ◇ | ○ | ◇ | ○ |
Request a quote
Peel Grinding Carbide Rods
We have the ability to produce cylindrical tools through peel grinding operations. To guarantee that our clients use our products more effectively, we may modify them to meet various needs while maintaining outstanding performance, industry-leading quality, quick response, and competent after-sales service.
Request a quote
Get in Touch
About Egret Tool
Egret Tool is more than just a cutting tools supplier, but as a trustful provider of custom carbide tooling solutions for milling, turning, holemaking and more machine tools. The carbide cutting tools from Egret Tool are widely used in a multitude of industry sectors such as automotive parts manufacturing, aerospace parts machining, mold making, electronic parts machining, and other processes where precision machining tools are needed. As a specialist of carbide cutters, we have the ability to develop a huge variety of custom cutting tools, including endmills, twist drills, indexable inserts, etc.
